RGB RF Remote Controller 5A (Multi Zone Touch Remote) RGB or RGBW

Control multiple zones with one remote (up to 10 zones but each zone can have any number of receivers).
Has built in effects that can chase and involve several zones.
Easy to access any color by a quick touch on the color wheel.
Ability to create custom colors by adjusting the intensity of each color.
Ability to sync multiple receivers together for synchronized fades.
Supports RGB and RGBW so you can control a 4th channel (for example Warm White) with the same remote.
Auto power off after a few seconds to extend battery life of the remote.
Speed and brightness adjustable even in fades.

To change the color of a single receptor follow the following procedure:
1. Press the power button in the remote if the remote is off.
2. Select the channel to be controlled pressing any of the 1-10 keys on the
remote:
3. Move your finger across the touch color wheel, until you see the color that
you want.

To change color of ALL the LED lighting Fixtures simultaneously.
To change the color of some or all the receptors follow the following procedure:
1. Press the power button in the remote if the remote is off.
2. Press in a rapid succession buttons from 1-10. For example, if we want to
change the color of receptor 1,2,3,4, and 5 we will press in a rapid
succession the buttons from 1-5 and then use the color wheel to change
color of that group of receptors.
Fast select of color and fine-tuning colors.
The above 4 color buttons are used to access very fast a primary color, and or
to create mixing of colors in a very easy way.
1. If you press the red button, you will see your selected receptors and LED
lights turn to red. If you press RED again, you will turn off the RED in all
selected receptors. This principle applies for the rest of the buttons
(Green, Blue and White)
2. Mixing colors: You can create a mix of color by pressing 2 or more
buttons. For example, if we want to create a “purple color” we need to
use RED and BLUE for this. Therefore press the red and then the blue
color.
3. Every time you press a color button, you either turn on the color or turn it
off.
a. Example: If we press the red button, we will get RED lights. If then
we press the Blue Button, we will get, Purple (Red + Blue). If now
we press the green button, we will get white lights (Red + Green +
Blue). If we now press the blue button we will turn off the blue, but
RED and green will still be on, therefore creating yellow (Red +
Green)

How to use the Color Effects programs.
1. First select the channels you want to control (1-10).
2. Press the “M” button and you will select the first program with color
effects.
3. If you press the M button again you will pause the current color chase
program.
4. If you press the M button again, you will enter program number 2.
See here how it works:
Program1 ---Pause---Program2----Pause---Program3---Pause---Program4---
Pause---Program5---Pause---Program6---Pause---Program7---Pause---
Program8---Pause---Program9---Pause---Program10---
Pause……..Program1…..
Each time you press the “M” button, you go through all the programs with a
pause function in between the programs.
Controlling Speed and Brightness of programs:
Once you selected the program of your choice, you can adjust the speed of the
program and brightness levels by using the Brightness and speed controls.

Changing Speed:
Use the S- and S+ on the remote to change and fine tune the speed at which
the colors change in any of the programs. There are 16 speed levels. The
fastest speed is 4 seconds for all the colors to cycle and the slowest speed is
256 seconds.

Changing Brightness:
Use the B- and B+ on the remote to change and fine-tune the brightness Levels
of the selected program.
Note: The B- and B+ also work when you have individual colors selected.

How to pair several receptors to the remote control
The LED Wizard remote control has 10 buttons. Each number button can
control 1 or more receptors.
Here's a configuration example: You have 5 different zones to control in
your installation. Therefore you will have 1 remote control and 5 receptors. You
will need to tell each receptor to what number channel they belong.
Once the receptors have been correctly wired and powered we will start to
define and pair each receptor with its own channel.
Step 1:
A. Press the red power button in the remote control
B. Now press any button from 1 to 10 depending in which channel you want to
assign to the receptor. In this case we will press button “1” in the remote.
C. Press the learning button in the receptor.
D. Immediately start sliding your finger in the rainbow circle
of the remote control, if correctly done, you will see the red
LED light blink in the receptor. It will blink for about 3
seconds. Once it stops blinking the receptor has been
correctly paired.
E: Repeat this with other receptors. You can pair all receptors to the same
channel, in this case 1, or have them in different channels 1-10.
If by any circumstance you wish to reprogram any of the receptors, you will
need to “reset” the receptor. To do this, simply press the learning button during
5 seconds until the red LED lights shuts off, and redo steps A-E above.